1WZ系列船用自吸式旋渦泵-大連富仕泵

 

WX系列為離心旋渦泵。 第一級工作輪為離心式，第二級工作輪為旋渦式的兩級懸臂式結構。泵的進口為軸向水平方向，出口為垂直向上。離心葉輪用葉輪螺母固定在軸上，而旋渦葉輪可在軸上沿軸向自由移動，以保證旋渦葉輪與泵體、泵蓋之間的軸向間隙兩側相等，允許用紙墊調(diào)整間隙，泵和電動機合裝在共同底座上。軸封可采用軟填料密封,也可采用機械密封, 裝拆方便；整泵結構為軸對稱,通用化, 標準化程度高, 因此安裝, 運行, 維護都十分方便；適用于輸送溫度不高于+150℃，粘度不大于5°E，無腐蝕性的，無固體顆粒的液體。

WX series for centrifugal vortex pumps. The first level work for centrifugal, the second round of the work for the spiral type wheel two-level cantilever structure. Pump of imported for axial horizontal. Export for vertical. Centrifugal impeller with impeller nut fixed in the shaft, and can be on the shaft eddies impeller along the axial move freely, to ensure that the spiral pump body, impeller pump cover with the axial gap between both sides equal, allow paper pad, pump and motor adjust clearance fits into common base. Shaft seal can use soft packing seal, also can use of mechanical seal, raplace singly; The whole pump structure for axisymmetric, universal, standardization degree high, therefore installation, operation, maintenance extremely is all convenient; Suitable for conveying temperature is not higher than +150℃, viscosity is not more than 5° E, non-corrosive, no solid particle fluid.

 

型號說明：Model Explanation 65WX₁-130

65—吸入口徑 Imbibe dia.

WX—離心旋渦泵 Centrifugal vortex pump

₁—電源為60Hz，50Hz時不帶“₁” Power is 60Hz. Without “₁” when it is 50Hz

130—揚程130米 Head 130m

 

型號 Type	流量Capacity		揚程 Head (m)	允許吸上 高度 HS(m)	轉速 Speed (r/min)	郊率 Efficiency (%)	軸功率 Shaft Power (kW)	電機功率 Motor power (kW)	葉輪直徑 Impeller Dia. (mm)	泵重/電機重 Weight (kg)
	(m3/h)	(l/s)
65WX-130	6.3	1.8	173	7	2900	28	10.8	15 Y160M2-2	135	70/135
	9	2.5	130	7	2900	34	9.35		135
	11.25	3.1	88	7	2900	34	7.92		135
65WX-140	10.8	3.0	186	7	2900	31	17.7	22 Y180M-2	150	70/180
	14.4	4.0	140	7	2900	38	14.45		150
	18	5.0	94	7	2900	37	12.45		150
65WX-150	17.25	4.8	200	7	2900	34	27.7	30 Y200L2-2	160	70/215
	21.6	6.0	150	7	2900	41	21.28		160
	27	7.5	95	7	2900	40	17.5		160